0 item(s)
View cart
You have no items in your shopping cart.
Safety
Parachute Pack Mounting Plate
Features:
1/8″ steel.
6″ x 6″ mounting hole pattern.
1″ center hole.
Made in the USA!
$35.00
Steering
6" Column Extension
Features:
6" length.
Fits standard 5-bolt Grant and MPI steering wheel pattern.
Constructed from TIG welded 4130 chromoly.
Weighs less than 1 pound.
Made in the USA!
$50.00
Ignition & Electrical
MSD HVC-2 Coil Bracket
Features:
Lightweight mounting solution for MSD HVC-2 coils.
Welds directly to 1-5/8" tube.
Made in the USA!
$25.00
G-body 1978-1988
Upper Coil-Over Brackets
Features:
Attaches upper coil-over in the stock shock location.
1" width.
Direct bolt-in.
Grade 8 Hardware included.
Made in the USA!
$50.00
Drivetrain
Chevy Crank Pulley Spacer
Features:
1/4" thick.
Spaces lower pulley out for proper pulley alignment after adding a motorplate.
Machined from 6061 aluminum.
Available for SBC and BBC.
Made in the USA!
$30.00
G-body 1978-1988
Lightweight Bumper Brackets
Did you know there are 8 different lengths and styles of bumper brackets across all years and models of G-bodies? Other companies want you to measure your factory bumper brackets...
$65.00
Interior
Steering
Weld-on Steering Wheel Hook
Features:
1/8" steel.
Radius to weld directly to 1 5/8" tube.
Fits any steering wheel.
Made in the USA!
$10.00
G-body 1978-1988
Manual Brake Conversion
Available as mounting block only, or as complete kit. Complete kits include mounting block, Strange Engineering master cylinder, pushrod, rod end, hardware, and installation instructions. Features: Fits 1978-1988 G-body Billet...
$135.00
G-body 1978-1988
Pre-Cut Motorplate
Features: Machined from 6061 aluminum. Pre-cut and profiled to to fit with engine in stock location. Available with notch to clear stock steering shaft, or no notch for rack &...
$155.00
G-body 1978-1988
Lower Control Arm Braces
Features: Fits 1978-1988 G-body Adds rigidity to factory lower control arm torque boxes. Prevents factory torque boxes from flexing forward on hard launches. Adds a layer of thickness to control...
$85.00
G-body 1978-1988
Bolt-in Kirkey Seat Brackets
Features: Fits 1978-1988 G-body Bolt-in design, no fabrication required. (factory bucket seat cars) Fits 15″-18.5″ Kirkey seats. Will also work with most other brand aluminum seats. Tons of mounting positions...
$175.00
Safety
Parachute Cord Tether
Features:
Gusseted steel parachute cord tether.
1.5″ inside width.
Available with or without 1/2″ i.d. pushbar pin receiver.
Grade 8 hardware and plastic bushing included.
Made in the USA!
$35.00
G-body 1978-1988
Driveshaft Safety Loop
Features: Direct bolt-on for 1978-1988 G-body. TIG welded. Fixture welded. 4130 chromoly construction. Less than 3 pounds. Bolts to factory floor brace using factory hardware. No fabrication required. Exceeds NHRA...
$85.00
G-body 1978-1988
A/C Heater Delete Plate
Features:
Fits 1978-1988 G-body
.063" 5052 Aluminum.
Direct bolt in using factory hardware.
Made in the USA!
$55.00
A-body 1964-1972
Lower Control Arm Braces
Features: Fits 1964-1972 A-body Adds rigidity to factory lower control arm torque boxes. Prevents factory torque boxes from flexing forward on hard launches. Adds a layer of thickness to control...
$85.00
G-body 1978-1988
Upper Control Arm Braces
Features: Fits 1978-1988 G-body Adds extra rigidity to factory upper control arm mounting points. Adds a layer of thickness to control arm bolt holes helping to prevent hole ovaling. Adds...
$75.00
